How to Cut Down a Small Tree with a Saw : 10 Steps [DIY]

how to cut down a small tree with a saw

Are you looking for an easy way to cut down a small tree? If you have the right tools and knowledge, you might want to consider taking it down yourself.

Using a saw would make the job easier, but how would you cut down a small tree with a saw? In this article, we’ll go over what the steps are for cutting down a tree using a saw.

How to Cut Down a Small Tree with a Saw in 10 Steps?

10 Simple Steps on How to Cut Down a Small Tree with a Saw

By following these 10 simple steps, you will be able to cut down a small tree with ease.

Step 01: Determine the Cutting tools and Tree

Make sure you cut down the right type of tree because not all trees have the same measurement for their circumference. Next, determine which tree cutting tools you’ll need.

Step 02: Get Your Saw Ready

After you know what needs to be cut, get out your saw and make sure it is in working condition. Then, place your saw halfway into the trunk of the tree until it comes across a good balance point. The blade of the saw should be in a perpendicular position to the trunk of the tree.

Step 03: Position the Tree Correctly

After you have determined what needs to be cut down, it’s time to position the tree properly for sawing. Place the saw above your balancing point and drop it down so that the blade gets halfway inserted into the trunk of the tree.

Step 04: Measure and Mark You’re Cut

Get your measuring tape and measure from the edge of the blade to where you need to make your cut. Once measured, place a marker on that spot so you can return back there when it’s time to cut.

Step 05: Make Saw Cuts on Both Sides

Make a cut on either side of your balancing point to ensure an accurate measurement is achieved when you are finished with all four cuts. The measurements must be equal or the saw will not fall down in the right position.

Step 06: Remove all Four Supports

Remove all support beams of the cut tree so that it can fall on its own. To ensure that your measurements are correct, you should use a 10 feet pole to measure if everything is level before cutting completely down. A cable or strap can also be used to support the tree as you cut it down.

Step 07: Cut the Trunk

Once you have prepared for the cut, start sawing into the trunk of your tree. You can use a chainsaw or an ax to make this process easier. If you’re using a chainsaw, remember that you might need someone’s help if it starts getting heavy and almost impossible to maneuver on your own.

Step 08: Prune the Top of the Tree

Cutaway any branches or leaves at the top of your tree to make sure they don’t get in the way when it starts falling. Remove anything that would change the course of your falling tree so you can keep everything as simple and straightforward as possible.

Step 09: Prepare for the Falling Tree

Get away from your tree and prepare yourself to fall down with it. Make sure you aren’t standing anywhere near the potential direction of where your tree might fall. You should also consider getting out any tools or devices that could get in the way while the tree is falling.

Step 10: Let the Tree Fall

Let your tree fall down from naturally. If it does not come down, you can add a cable underneath the trunk to push it closer to the ground before removing the remaining support beams.

Once your tree has been cut down, you should be able to remove all of the pieces and re-purpose the wood as firewood or other ways to use the wood product.

Types of Saws to Cut Small Trees

Types of Saws to Cut Small Trees

There are many types of saws you can use to cut down a tree. Here are some of the most common types:


Handsaws are useful if you have a long tree branch or stem that needs to be removed. It is also good for cutting down bigger trees because the wider blade gives you a lot of power when it comes up against thicker pieces of wood.

Folding Saw

A folding saw is a type of hand saw compact and easy to carry, making it a good option for those who want to take their tools with them on the go. This hand saw is especially great if you need to work in places where there isn’t much room or an effective source of power.

Pruning Saw

You can use a pruning saw that is a part of the hand saw. This handsaw is ideal for cutting branches under 1″ in diameter. It is lightweight, easy to handle, and very effective.

Bow Saw

A bow saw is also the type of hand saw that is used to cut through tree limbs that are bigger in diameter. It’s a good option if you’re working on a big-sized project and need to get precise cuts every time.

Crosscut Saw

If you need to make a lot of cuts, a crosscut saw is the best option. This type of saw is often used for wood that’s been cut down from other sources or trees that have already been processed into smaller pieces.


A chainsaw is the easiest option for cutting down trees since it requires less physical effort to get the job done. Use a felling wedge when cutting down a large tree to make sure the chainsaw engine does not kick back.

A gas-powered chainsaw is good for cutting through bigger pieces of wood with its powerful engine.

The electric chainsaw also works well for this type of project, just be ready to deal with a cord and prepare to haul out the tree trunk.

ToolsAdventure is a good place to learn about chainsaw mill for beginners.

Rope Chainsaw

A rope chainsaw is like a manual hand-powered chainsaw that works by having you pull on it continuously. You’ll probably need to use this saw in conjunction with another type of saw when it comes time to cut down a small tree.

Reciprocating Saw

A reciprocating saw is used to cut through wood with its oscillating action. It’s similar to using a standard saw, but it’s easier to get more accurately cut pieces you can use for your wood product.

Pole Saw

A pole saw is easy to use if you’re looking for something lightweight that doesn’t take up much space. This type of saw allows you to get the perfect cut every single time without making any mistakes or needing assistance.

Cutting down a tree can be a challenging task that requires a lot of physical effort and skill. Using the right type of saw can help smooth out the process and make it a lot easier.

Safety Consideration

Safety Consideration

It is very important that you know what you’re doing when cutting down a tree with a saw so it does not fall on top of anyone or anything and cause damage.

  • Always wear protective eyes and headgear when you’re using a chainsaw or any other type of saw.
  • Be sure to check the weather and ground conditions to ensure that it’s safe for you to begin cutting down your tree.
  • Make sure you have an escape route planned in case something goes wrong and the tree does start to fall toward you as you’re attempting to cut it down.
  • If your tree is very tall, make sure there aren’t any power lines nearby that could come into contact with branches and cause a power outage.
  • When you get down to cutting the trunk of your tree, take small bites so it doesn’t fall too fast and surprise you.
  • If there are any other people or animals around when your tree begins to fall, have a plan in place for how to handle that situation if it occurs.

Lastly, always remember to stay safe while you’re cutting down a tree with a saw.


Hope you were able to read all the way through this article and learn something new about how to cut down a tree with a saw.

Owning your own saw can be really helpful for those times when you need to remove dead trees on your property but don’t want to bring in an outside contractor.

How to Cut Down a Small Tree with a Saw : 10 Steps [DIY]
Scroll to top